bending strength的例句大全

The cement strength of grade ~ # 325 ~~ # 425 , and has high-early strength and high bending strength.

水泥标号可达325～ 425, 且具有早期强度及抗折强度高等优点.

SEM analysis indicated that evenly distributed fine crystal grain was the reason of good bending strength.

SEM分析认为:造成材料抗弯强度增加缓慢或下降的原因是材料晶粒粗大,晶粒分布不均匀.

The Bending strength for concrete bonding was over 7 MPa with ester crete-p and 8 Mpa with Epcrete-p .

用epcretep粘合 的混凝土试件的抗折强度可达到 8MPa 以上.

At transition region, the sea ice bending strength reached the maximum value.

海冰的弯曲强度随着应力速率的增加,经过延性、过渡和脆性三个阶段,在过渡区, 海冰的弯曲强度达到最大值.

Nano-scale ceramic composites may have high bending strength and fracture toughness.

纳米复合 陶瓷材料可以极大地提高抗弯强度和断裂韧性.

The coated twisty blade patterns possesses higher bending strength and hardness than the uncoated ones.

带涂层可熔扭曲叶片模具有更高抗弯强度和硬度,可以适应制芯操作.

The Izod impact strength, the bending strength and tensile strength were tested.

同时,测试了该材料的冲击强度 、 弯曲强度和拉伸强度.

In addition, there is positive correlation between fractal dimension and bending strength , bending elastic modulus.

另外, 发现分形维数与抗弯弹性模量 、 抗弯强度之间存在正相关趋势.

The relationship between bending modulus of elasticity and bending strength was also linear.

抗弯弹性模量与抗弯强度具有密切的线性关系.

The tensile strength and the bending modulus of RHDPE/ EVA/ MWRP blend increased by 35% and 25% respectively when the waste rubber powder was modified by self-made surface modifier ACDI.

废胶粉经自制表面改性剂ACDI预处理后，其相应的RHDPE/EVA/MWRP体系的拉伸强度和弯曲模量分别增加35%和25%，而对共混物的其它性能影响不大。

The material has better mechanical properties than that of natural tooth in bending strength ( 142MPa), fracture toughness ( 4.75MPam~ ( 1/ 2)), hardness ( VHN 5.33GPa).

并具有比天然牙更优的力学性质，如抗弯强度（142MPa）、断裂韧性（4.75MPam~（1/2）），硬度（VHN5.33GPa）等。

Three rattan materials all have bigger bending strength and smaller MOE.

三种藤材均具有抗弯强度大（相对于弹性模量而言大）而抗弯弹性模量小的特点。

As the bending strength of sodium silicate sand cured by ester method is much higher than that cured by CO_2 method the analysis shows that the key point is the refinement of grains of silicate gel.

分析了酯法比CO2法水玻璃砂强度高的原因，指出充分发挥水玻璃粘结效率的关键在于细化水玻璃凝胶胶位。

Research on Equivalent Bending Strength of Cermet Cladding Material for Clad in Press Condition

金属陶瓷硬质覆层材料覆层受压时的等效抗弯强度研究

Bending strength, bulk density and thermal dilatation of molybdenum slag glass-ceramics are smaller when adding molybdenum slag more while obvious porosity, water-absorbing capacity, rate of shrinkage are bigger, the performance of Acidresistivity and alkali resistivity are excellent.

随着钼渣添加量增加，钼渣微晶玻璃的抗折强度、体积密度和热膨胀系数减小，而显气孔率、吸水率、收缩率增大，耐酸耐碱性能好。

Therefore Vertical WEDM with Rotation Wire can enhance the bending strength of the wire electrode and reduce the vibration of wire electrode so as to prevent the happening of filament breakage.

因此，立式回转线切割可以提高电极丝的抗弯强度，降低电极丝振动，从而降低断丝现象的发生。

Strength checking formula for blanking punch in current documents have been reviewed and the anti-bending ability of blanking punch is discussed.

查阅和分析现有文献中给出的冲裁凸模强度校核公式，针对凸模抗压弯能力的强度校核问题进行了讨论。

The Analysis of the Shear Strength of Reinforced Concrete Restrained Members under Biaxial Bending

钢筋砼双向受弯约束梁抗剪强度的试验研究

The equivalent section method on the strength of reinforced concrete columns with biaxial bending

钢筋混凝土双向偏压构件承载力计算的等效截面法

Strength Calculation and Its Simplified Method for Reinforced Concrete Beams Subject to Biaxial Bending

钢筋砼双向受弯构件的强度计算及其简化方法